Inspection Report

Business Name
Fate Brewing Company

Business Address
201 E SOUTHERN AVE TEMPE AZ 85282

Permit Number
FD-66915

Permit Type
Food Establishment - Eating & Drinking

Inspection Purpose
Food Routine Inspection

Inspection Date
11/13/2024

Grade
Not Participating

Priority Violation
1

Inspection Status
Completed

Violations

Violation #: 16

Description: Food-Contact Surfaces: Cleaned and Sanitized

Comments:

PRIORITY VIOLATION-4-501.114 (A-E) - Priority: Manual and Mechanical Warewashing Equipment, Chemical Sanitization- Temperature, pH, Concentration and Hardness. For a permanent fix to this violation, check out these simple tools in our Active Managerial Control Toolbox, made especially for you. https://www.maricopa.gov/4574/AMC-Toolbox---Food-Contact-Surfaces.

Addl Notes: Observed the mechanical bar dish machine that uses chlorine to sanitize, with a concentration of 0 ppm. Air bubbles were present in the line and priming did not fix the issue. PIC switch the sanitizer chemical bottle to a new bottle at time of inspection. Once the bottle was switched the machine was sanitizing with the proper chlorine concentration, 50-100 ppm. Discussed the importance of monitoring the concentration levels to ensure that food contact surfaces are being sanitized with PIC. Food-contact surfaces must be properly sanitized after washing and rinsing. Discussed the importance of proper sanitizer levels and proper monitoring of sanitizer levels. Corrective Action: Corrected at time of inspection.

4-501.112 - Priority Foundation: Mechanical Warewashing Equipment, Hot Water Sanitization Temperatures. For a permanent fix to this violation, check out these simple tools in our Active Managerial Control Toolbox, made especially for you. https://www.maricopa.gov/4574/AMC-Toolbox---Food-Contact-Surfaces. Addl Notes: Observed the high-temperature dish machine reaching a maximum rinse temperature of 154.3*F. Informed PIC that the sanitizing rinse water temperature needs to be at least 160*F at the surface temperature to properly sanitize food contact surfaces. PIC called the company for assistance and ran the machine a few times. Upon, testing the next two full cycles, the maximum temperature reached was 171.3*F. Suggested to PIC running the machine a few times with a waterproof min/max thermometer before starting the dishes, to ensure the water is at least 160*F and the machine is properly working. PIC called to have the machine serviced for the leak and the low temperature. When food-contact surfaces are being sanitized with hot water in a dish machine, the surface temperature must reach at least 160°F as measured by an irreversible registering temperature measuring device to destroy pathogens that may remain on such surfaces after cleaning. Food-contact surfaces were properly sanitized at time of inspection. Corrective Action: Corrected at time of inspection.

Violation #: 51

Description: Plumbing Installed; Proper Backflow Devices

Comments:

5-205.15 (B) - Core: System Maintained in Good Repair; Maintained Addl Notes: Observed a pipe with a mushroom cap on the back of the mechanical ware washing machine in the kitchen, leaking a large amount of water with ever rinse cycle. The water is pooling under the machine in the corner. Informed PIC that the machine needs to be serviced and brought back into good repair. Discussed the establishment's process for cleaning up the water on the floor with PIC. All plumbing must be maintained in good repair at all times. Must repair all plumbing to a state of good repair prior to next routine inspection. Corrective Action: Correct prior to next routine inspection.

Comments/Details

No County legal action will result from this inspection.

"A" for Food Safety

Through our grading system, Maricopa County Environmental Services Department provides at-a-glance indications of how food establishments perform during food safety inspections. This system is designed to grade food establishments in terms of food safety requirements and provide recognition to those who choose to participate.

How does it work?

The issuance of grade cards to food establishments is based on voluntary participation. The person in charge, who is present during the inspection, will be asked whether they would like to participate in the Grading System. This will be decided prior to each inspection. If an establishment does not participate in the Grading System, Not Participating or NP will appear on the inspection report, and the inspection will still occur. If an establishment does participate, a grade of A, B, C, or D will be determined at the conclusion of the inspection using the Grading System chart below. Participating establishments will then be provided with a grade card that can be posted in the establishment. The status of the establishment’s grade will also appear on the Restaurant Ratings page of the department’s website.

How can I determine the grade?

The Grading System chart can be used to determine grades earned for establishments that do not participate. Grades are determined by the number of Priority and Priority Foundation violations received at the time of inspection. Violation types are defined in general terms below.

Definitions

Priority Violation: Major violation that directly contributes to increasing the risk of foodborne illness or injury (e.g. Food employees do not properly wash hands when required).
Priority Foundation Violation: Minor violation that does not directly contribute to an increased risk of foodborne illness but failure to correct this violation may lead to the occurrence of a priority violation. For example, hand washing soap and paper towels not available at hand wash sink (may lead directly to food employees not properly washing hands when required).
Core Violation: Minor violation that relates to general maintenance and sanitation (e.g. No sign reminding employees to wash hands).
Cutting Edge Program: All county food-related establishments can partner with Maricopa County to implement a proactive approach to reducing foodborne illness risk factors by implementing food safety systems that include policies, training, and verification processes. Partners enrolled in the Cutting Edge Program receive an A+ when an A is earned.

Grading System The matrix below is used to grade food inspections under the voluntary grading system.
Violation Category	Grade A	Grade B	Grade B	Grade B	Grade B	Grade B	Grade B	Grade B	Grade C	Grade C	Grade C	Grade C	Grade C	Grade C	Grade D	Grade D
Priority	0	0	0	0	0	1	1	1	0	1	1	2	2	2	more than 2	more than 3
Priority Foundation	0	1	2	3	4	0	1	2	5	3	4	0	1	2	more than 3	more than 0

Any legal action for a pattern of non-compliance or permit suspension results in a D.